How To Build A Custom Range Hood Cover Youtube
When I think of builder grade, the first place I remember of is the kitchen. More than whatever other surface area of the house, kitchens tend to exist at the pinnacle of everyone's "what I want to alter most my home" list. And where to start with taking your kitchen from builder-grade to beautiful (since that's kind of our thing)? With the cabinets! It all starts with painting (usually), merely at that place are lots of great options across paint, too. Our guest today is showing how she upgraded her cabinets with a DIY custom range hood (for under $50!):
Curlicue down for Jill'southward awesome tutorial, and check out these other swell means to show your kitchen cabinets some DIY dear:
Add Crown Molding to Cabinets (Painted or Wood) | Remodelaholic
Drinking glass-Front Cabinet | Scissors and Spatulas featured on Remodelaholic
Custom Plate Rack Cabinet | Bluish Roof Cabin featured on Remodelaholic
Replace Cabinets With Open up Shelving | Low Country Living featured on Remodelaholic
How to Build a Custom Range Hood
past Jill of The Rozy Home
Hi everyone! I'g Jill from The Rozy Abode and I've been blogging my way through a remodel for the last few months. I am a huge fan of Remodelaholic and have getting inspired from Cassity and the gang for the last few years. Imagine my surprise when they asked me to do a guest mail service near my $50 Custom Range Hood!
We bought our business firm in 2010, 2 months after the nascence of our son, and I have been working non-stop since then to make our business firm our home. When we walked into our abode the showtime time, I looked at my husband and said "nope." Just then something wonderful happened. We went outside on the upper deck and saw the view. Oh the view! I often call information technology our lilliputian piece of heaven in the center of the Texas loma country. I took a minute, walked effectually the house and decided that I could make this place beautiful. It had a good layout, the rooms were big and information technology had a ton of potential.
One of the first projects we worked on was the kitchen. Information technology looked a piddling something like this when we bought information technology.
The first thing I did was pigment the cabinets and remove that dreadful microwave from over the stove. Why did I remove the microwave? Even though I know there is no prove of it being an issue, I just don't similar having a microwave buzzing next to my caput while I'm cooking. My solution was to but take information technology down and replace it with a vent.
One of the questions/comments I hear the nigh is "What was incorrect with it like that?" or "It looked fine like information technology was" That's the matter – information technology looked fine. Naught spectacular – just fine. Since our kitchen opens upwards to our living area, I wait at it – a lot! I wanted more personality. Oh and did I mention that vent I purchased fit perfectly into the cabinets? So perfect, in fact, that I couldn't plug it in. For the final two years I had no vent, and no light.
Helpful hint: When ordering a vent to use for this project, make certain y'all order 1 several inches smaller (width and depth) than your cabinets.Seems similar common sense, right? But when y'all are new to remodeling/DIY things that should be common sense aren't always so black and white.
Also, a little note about the vent itself (because boy have I gotten a ton of questions on this part of information technology): you lot can use an exterior venting unit for this projection. The vent I selected was recirculating considering that is the fashion my home was set. I had quotes to become an outside venting arrangement put in merely information technology was in excess of $1000 (the side of our habitation was rock and then it would have required a masonry expert in addition to plumbing/electric). Because this tutorial is for the range hood, the vent you use makes no departure (recirculating or outside venting).
Building the range hood:
For your convenience, this mail service contains affiliate links, which permit us to go along providing y'all lots of decorating and DIY ideas at no toll to you. Learn more here .
The materials:
- 1 4X8 Birch Plywood Panel
- one Ten ii X 8 Back up Boards
- i x 3 X eight Pino Board (for top face)
- 1 X 4 10 8 Pino Boards (for bottom face)
- 2 8 foot lattice pieces: $seven.28
- Liquid Blast: $2.52
- Trim Pieces: $8.52
The project:
Begin past taking off the chiffonier doors and removing the bottom of the cabinet. I too knocked out the front support piece. At present you lot may be wondering why wouldn't I simply remove the center cabinet unit. I couldn't. The side and centre cabinets are all one piece – bummer! If you are lucky plenty to have a separate center cabinet, all you take to do is remove that section.
I'm sure you noticed I didn't move the stove (or fifty-fifty the tea kettle). My husband croaky the cooktop last year so it just has one operation burner. Please, please, please move or at least embrace your stove prior to doing this project.
After demoing and cleaning, decide how far yous desire the hood to projection out. I played with a few varying lengths before opting for 16 inches. Next, bladder in the two side supports, level them up and adhere them to the next cabinets using a blast gun.
Add the front and back supports.
Remember how I said the vent fit just perfectly? Well because of that I had to attach the vents to the side of the supports. Since all of you volition be purchasing a vent that is smaller than the space provided, I would recommend doing the following:
Measure the width of your cabinets in the front and the back (they should be the same, just sometimes they can be off by a one/2 inch or and then).
Cut 2 support beams to this width.
Adjacent, cut ii support beams to the overall length y'all decided on for the range hood (for me it was 16 inches).
Attach the supports together, creating a box frame. Do this outside of the cabinet space (in your workshop).
Next, cut a 3/4 inch thick piece of plywood to the overall width and length of the finished box frame. Prepare the vent on top of the plywood and draw an outline. Cut out the outlined department. Attach the plywood to the bottom of the box frame.
Attach the box frame to cabinet.
Now we are all on the same folio!
Attach the vent to the supports.
Install the vent (ie plug it in, adhere the exterior venting, if needed, etc).
Next, add a front face up to the bottom support. Information technology should be roughly one/2 inch longer than the support and should exist mitered to 45 degrees on both ends.
Adjacent measure the amount of exposed supports on the side and cutting a face front for each side (again with mitered edges).
Adhere a thinner face up front end to the superlative of your cabinet frame (the top face front is the same length as the bottom face front end and should besides be mitered at the ends).
Depending on how far your elevation face front sticks out, you lot will need to cut side face fronts for the upper section as well.
Measure the length between the superlative and bottom face up front and cut three supports beams to that size. Attach them to the dorsum of the face up fronts (I mitered the ends of the boards so that they would attach but behind the face fronts).
After adding the supports, measured the open area from the outside of the left support to the outside of the right support and from the top confront front to the bottom.
Using these measurements,cutting out a plywood square.
Attach the plywood to the supports using a nail gun.
Because the hood is slanted, the plywood should sit correct behind both the upper and lower face fronts.
Next, determine the angle of the side pieces. For lack of a ameliorate option, I folded a slice of cardboard over the side and and then cut the paper-thin to size.
Using the cracking cardboard template, trace out the pattern on a piece of plywood and cut. Attach to supports using a nail gun.
Mine weren't perfect only they didn't need to exist (the lattice and caulk volition cover up the edges).
Afterward attaching the sides, sand the entire range hood.
Next, cut two pieces of lattice to the width of the eye plywood area (making certain to miter them on the edges).
Measure the length between the upper and lower lattice piece and cut 5 pieces of lattice to this length. Attach in as spaced segments across the front end of the plywood. Make certain y'all have a slice of lattice on each edge – this will help "disguise" those imperfect side pieces.
If you lot want to bandbox information technology up, add trim to the superlative and lesser face fronts. I grabbed some trim I had in the garage. Feel costless to go creative and make it your ain at this point.
After caulking and filling in the boom holes, sand, prime number and paint. And then sit down back and marvel at your handy work!
So there you have information technology! Four hours and $fifty laters, my kitchen gained a lot of personality.
For you budget-savvy DIYers, here is how the toll bankrupt downwardly.
- Birch Plywood Panel: $ten.67
- 1 Ten 2 X 8 Support Boards: $2.61
- ane ten three X 8 Pino Board (for tiptop face): $v.43
- 1 X iv 10 viii Pine Boards (for lesser face up): $8.64
- 2 8 foot lattice pieces: $7.28
- Liquid Blast: $2.52
- Trim Pieces: $viii.52
- Total: $45.67!
Note: This doesn't include the crown moulding. I was replacing all of that on my cabinets anyway and so I already had it on paw.
Jill, I love information technology! What a great update for such a small investment, both time and money. I love kitchens with personality!
Pay Jill a visit at The Rozy Home and run across all the other peachy things she's doing in her abode!
UPDATE: Jill painted her range hood to await like the gorgeous farmhouse way metal range hoods. So gorgeous! Cheque out the details here.
Source: https://www.remodelaholic.com/diy-custom-range-hood-how-to/
Posted by: radfordborre1967.blogspot.com
0 Response to "How To Build A Custom Range Hood Cover Youtube"
Post a Comment